4-Input, 4-Output analog-auf-Dante Interface mit Kopfhörermonitoring
EINGESTELLTES PRODUKT

User Guide
Das MD-4 4×4 Analog-zu-Dante Interface ist ein einfaches, aber hoch-performantes Interface, um analoges Audio mit Dante Audio-Netzwerken zu verbinden.
Vier hochverstärkende Mikrofon- oder Line-Level-Inputs sind für die Verbindung zum Dante Audio-Netzwerk verfügbar.
Zusätzlich können bis zu vier Dante-Signale an den vier analogen Line-Ausgänge ausgegeben werden.
Die jeweiligen Ein- und Ausgänge können flexibel zur Qualiäts- und Pegelkontrolle auf den Kopfhörer-Monitorausgang geroutet werden.
Technical Details |
---|
Network Audio Technology |
Type: Dante audio-over-Ethernet |
Bit Depth: up to 24 |
Sampling Rate: 48 kHz |
Number of Transmitter (Output) Channels: 4 |
Number of Receiver (Input) Channels: 4 |
Dante Audio Flows: 4; 2 transmitter, 2 receiver |
Network Interface |
Type: twisted-pair Ethernet |
Data Rate: 100 Mbs (10 Mbs not supported; 1000 Mbs GigE Ethernet not supported unless falls back to 100 Mbs) |
Mic/Line Inputs: 4 |
Compatibility: dynamic or phantom-powered mics; line-level sources |
Type: 3-pin female XLR, analog, electronically balanced, capacitor coupled |
Impedance: 4 k ohms, nominal |
Gain: 0 dB (line), 10 dB, 19-70 dB in 3 dB steps (total 20 choices) |
Maximum Level: +18, +20, or +24 dBu, configurable, 0 dB gain selected, results in Dante digital output level of 0 dBFS |
EIN: 123 dBu, 22 kHz bandwidth, 70 dB gain, 150 ohm source resistance |
Dynamic Range: >116 dB, 0 dB gain, A-weighted |
Distortion (THD+N): more than 0.001% (101 dB) at 1 dBFS, 40 dB gain, 22 kHz bandwidth |
Frequency Response: +0.0/0.5 dB, 22 Hz to 22 kHz, HPF off |
High-Pass Filter (HPF): 6 dB at 75 Hz, 18 dB per octave, on/off selectable per channel |
Phantom Power: P48 per IEC 61938:2013 standard, +46 volts DC nominal, on/off selectable per channel |
Meters: 4, one 8-segment LED per input |
Status LEDs: 3, P48, HPF, input channel selected |
Line Outputs: 4 |
Type: analog, electronically balanced, capacitor coupled, intended to drive balanced or unbalanced loads of 2k ohms or greater, 3-pin XLR |
Source Impedance: 200 ohms |
Nominal Level: +4, 0, or 2 dBu, selectable, reference 20 dBFS |
Maximum Level: +18, +20, or +24 dBu, configurable, with 0 dBFS on Dante input |
Dynamic Range: >119 dB, A-weighted |
Distortion (THD+N): 0.0012% (99 dB), measured at 1 dBFS, 22 kHz bandwidth |
Frequency Response: ±0.1 dB, 20 Hz to 20 kHz |
Audio Monitor: |
Source: mic/line inputs or line outputs, selectable as monaural or stereo |
Meters: 2, 8-segment LED |
Headphone/Monitor Output: |
Type: stereo (dual-channel), when jack on front panel is used jack on back panel automatically disconnects |
Compatibility: intended for connection to stereo headphones with nominal impedance of 100 ohms or greater |
Maximum Output Voltage: 4.9 volts RMS, 1 kHz, 150 ohm load |
Frequency Response: +0/1.4 dB, 20 Hz to 20 kHz |
Distortion (THD+N): 0.005% |
Dynamic Range: >100 dB |
Connectors: |
Ethernet: Neutrik etherCON RJ45 |
Headphone Outputs: 3-conductor ¼-inch jack |
Factory: USB type A receptacle used only for application firmware updates |
AC Mains: 3-blade, IEC 320 C14-compatible (mates with IEC 320 C13) |
DC Input: 4-pin male XLR |
Power Source: |
AC Mains: 100 to 240 volts, +10/15%, 50/60 Hz, 15 watt maximum |
DC Input: 10-18 volts DC, 0.x A maximum @ 12 volts; 1.1 A maximum @ 10 volts; current draw when AC present is less than 100 uA |
Chassis Dimensions: |
19.0 inches wide (48.3 cm) |
1.72 inches high (4.4 cm) |
8.4 inches deep (21.3 cm) |
1U in a standard 19-inch rack |
Stereo Out |
2ch unbalanced stereo 3.5 mm for use with > 6k ohm inputs |
Max Stereo Out Level: '+7.8dBu 100Kohm load |
Headphones Out: 3.5 mm Stereo |
Weight: |
3.5 pounds (1.6 kg) |
Specifications and information contained in this User Guide are subject to change without notice. |